05-12-2018 05:04 AM
We recently upgraded our infastructure from Cisco to Brocade devices. Im going to include a show version output but its a b7450 48port model. Earlier I recieved a complaint from a client regarding loss of internet connecvitity. After investigating the issue I realized that a Cisco 8841 phone was not powering up and since the phone wasnt powering up it wasnt sharing the network connecvitity. When remove the phone from the equation the computer authenticates ( dot1x ) with no issues. The first thing I did was validate the power inline settings.
1#show inline power Power Capacity: Total is 748000 mWatts. Current Free is 726222 mWatts. Power Allocations: Requests Honored 57 times Port Admin Oper ---Power(mWatts)--- PD Type PD Class Pri Fault/ State State Consumed Allocated Error -------------------------------------------------------------------------- 1/1/1 On Off 0 0 n/a n/a 3 n/a 1/1/2 On Off 0 0 n/a n/a 3 n/a 1/1/3 On Off 0 0 n/a n/a 3 n/a 1/1/4 On Off 0 0 n/a n/a 3 n/a 1/1/5 On Off 0 0 n/a n/a 3 n/a 1/1/6 On Off 0 0 n/a n/a 1 n/a 1/1/7 On Off 0 0 n/a n/a 3 n/a 1/1/8 On Off 0 0 n/a n/a 3 n/a 1/1/9 On Off 0 0 n/a n/a 3 n/a 1/1/10 On Off 0 0 n/a n/a 3 n/a 1/1/11 On Off 0 0 n/a n/a 3 n/a 1/1/12 On Off 0 0 n/a n/a 3 n/a 1/1/13 On Off 0 0 n/a n/a 3 n/a 1/1/14 On Off 0 0 n/a n/a 3 n/a
After the power settings were checked I verified that the port was enabled and was functioning. I also bounched the port for good measure with the disable/enable command but that didnt seem to yield any results. What could possible be wrong with the device? With so much power available to the switch why arent the VoIP phones getting power with the configuration settings are correct? My gut is telling me there may be something wrong with the switch's firmware so Ill go ahead and include the show version.
#show ver Copyright (c) 1996-2015 Brocade Communications Systems, Inc. All rights reserved. UNIT 1: compiled on May 22 2017 at 22:31:09 labeled as SPS08040bc (22651786 bytes) from Primary SPS08040bc.bin SW: Version 08.0.40bcT211 Compressed Boot-Monitor Image size = 786944, Version:10.1.06T215 (spz10106) Compiled on Mon Dec 14 21:11:21 2015 HW: Stackable ICX7450-48-HPOE Internal USB: Serial #: Vendor: ATP Electronics, Total size = 1919 MB ========================================================================== UNIT 1: SL 1: ICX7450-48P POE 48-port Management Module Serial #:CYR3341M07S License: BASE_SOFT_PACKAGE (LID: eatIIJGoFMu) P-ASIC 0: type B548, rev 01 Chip BCM56548_A0 ========================================================================== UNIT 1: SL 2: ICX7400-4X10GF 4-port 40G Module Serial #:CYV3336M1E8 ========================================================================== UNIT 1: SL 3: ICX7400-1X40GQ 1-port 40G Module Serial #:CYX3341M041 ========================================================================== UNIT 1: SL 4: ICX7400-1X40GQ 1-port 40G Module Serial #:CYX3341M0GW ========================================================================== 1000 MHz ARM processor ARMv7 88 MHz bus 8192 KB boot flash memory 2048 MB code flash memory 2048 MB DRAM STACKID 1 system uptime is 17 day(s) 3 hour(s) 51 minute(s) 49 second(s) The system started at 08:17:54 GMT+00 Wed Apr 25 2018 The system : started=cold start
Its also worth mentniong that I tested a few other ports and I was able to get one port working 1/1/27. The ports configuration is identical to other ports on the switch but this one seems to be one of the few ports actually providing power:
#show run int ethernet 1/1/27 interface ethernet 1/1/27 authentication source-guard-protection enable dot1x port-control auto port-name portuse;bld#;rm#;loc#;jack# no dhcp snooping relay information inline power broadcast limit 49152 multicast limit 49152 unknown-unicast limit 49152 stp-bpdu-guard 1/1/27 On On 3300 6378 802.3af Class 2 3 n/a
05-14-2018 12:05 PM
You can reach the direct ICX forum quest over at the ICX Ruckus Forum below >>> https://forums.ruckuswireless.com/ruckuswireless/categories/ruckuswireless_icx_campus_switches_and_general_switching_questions
Brocade Community Manager
05-21-2018 02:15 AM - edited 05-23-2018 03:33 AM
follow these steps to eliminate that error
Verify that the powered device works on different ports and that the hassle is handiest on one port.
Step 2 Use the display run and show interface repute privileged EXEC commands to verify that the port isn't always shut down. (maximum Cisco switches flip off port energy whilst the port shuts down.)
Step 3 Use the display interface repute privileged EXEC command to confirm that the switch port is not blunders disabled.
Step 4 Use the display run and show electricity inline interface-identity privileged EXEC command to confirm that the strength inline in no way interface configuration command isn't configured on the port.
Step five affirm that the Ethernet cable from the smartphone to the transfer port is right. connect a recognised excellent non-PoE Ethernet tool to the Ethernet cable, and ensure that it establishes a hyperlink and exchanges site visitors with any other host.
Step 6 verify that the entire cable length from the switch the front panel to the connected tool (powered tool) isn't more than 100 meters. For more information, see the cable diagnostics phase in the switch software program configuration guide.
Step 7 Disconnect the Ethernet cable from the transfer port. Use a short Ethernet cable to attach a regarded proper Ethernet tool to this transfer port (no longer at a patch panel). confirm that the device establishes an Ethernet link and exchanges visitors with every other host, or ping the port VLAN SVI. subsequent, connect a powered tool to this port, and verify that it powers on. If it does no longer energy on, go to Step 8.
Step eight Use the display inline electricity and show inline power detail privileged EXEC instructions to examine the number of linked powered gadgets towards the transfer electricity budget (to be had PoE). verify that switch strength finances can electricity the device