Fibre Channel (SAN)

Reply
Occasional Contributor
Posts: 9
Registered: ‎11-30-2017

snmpwalk is giving error No Such Object available on this agent at this OID

Hello Team,

Snmpwalk is giving  the below error.

 

/usr/bin/snmpwalk -v 3 -l noAuthNoPriv -u snmpuser1 xx.xx.xx.xx 1.3.6.1.3.94 -O n
.1.3.6.1.3.94 = No Such Object available on this agent at this OID

 

This is a IBM-Brocade switch. 

 

We have many other unit which is working fine,  there are  few devices where we are getting the above error. 

 

Switch Details:
switchType: 62.0 (DCX-8 Gb 798-port core fabric backbone)
Vendor:-IBM-Brocade
Frimware:v7.4.1d

snmpConfig --show snmpv3
SNMP Informs = 0 (OFF)

SNMPv3 USM configuration:
User 1 (rw): snmpadmin1
Auth Protocol: noAuth
Priv Protocol: noPriv
User 2 (rw): snmpadmin2
Auth Protocol: noAuth
Priv Protocol: noPriv
User 3 (rw): snmpadmin3
Auth Protocol: noAuth
Priv Protocol: noPriv
User 4 (ro): snmpuser1
Auth Protocol: noAuth
Priv Protocol: noPriv
User 5 (ro): snmpuser2
Auth Protocol: noAuth
Priv Protocol: noPriv
User 6 (ro): admin
Auth Protocol: noAuth
Priv Protocol: noPriv

SNMPv3 Trap/Informs configuration:
Trap Entry 1: 10.237.129.29
Trap Port: 162
Trap User: snmpadmin1
Trap recipient Severity level: 4
Notify Type: TRAP(1)
Trap Entry 2: 10.236.138.123
Trap Port: 162
Trap User: snmpadmin1
Trap recipient Severity level: 4
Notify Type: TRAP(1)
Trap Entry 3: No trap recipient configured yet
Notify Type: TRAP(1)
Trap Entry 4: No trap recipient configured yet
Notify Type: TRAP(1)
Trap Entry 5: No trap recipient configured yet
Notify Type: TRAP(1)
Trap Entry 6: No trap recipient configured yet
Notify Type: TRAP(1)


snmpTraps --show

# |Mib Name |Supported Traps
---|----------------|--------------------------------
001|SW-MIB |sw-fc-port-scn
| |sw-ip-v6-change-trap
| |sw-pmgr-event-trap
| |sw-event-trap
| |sw-fabric-reconfig-trap
| |sw-fabric-segment-trap
| |sw-state-change-trap
| |sw-zone-config-change-trap
| |sw-port-move-trap
| |sw-brcd-generic-trap
| |sw-device-status-trap
002|FICON-MIB |link-rnid-device-registration
| |link-rnid-device-deregistration
| |link-lirr-listener-added
| |link-lirr-listener-removed
| |link-rlir-failure-incident
003|FA-MIB |conn-unit-status-change
| |conn-unit-port-status-change
| |conn-unit-event-trap
004|MIB-2 |cold-restart-trap
| |warm-restart-trap
005|IF-MIB |if-link-up-trap
| |if-link-down-trap
006|RFC1157 |snmp-authetication-trap
007|HA-MIB |fru-status-change-trap
| |fru-history-trap
| |cp-status-change-trap
008|BD-MIB |bd-trap
| |bd-clear-trap
009|MAPS-MIB |maps-trap
010|T11-FC-ZONE-SERVER-MIB|t11ZsRequestRejectNotify
| |t11ZsMergeSuccessNotify
| |t11ZsMergeFailureNotify
| |t11ZsDefZoneChangeNotify
| |t11ZsActivateNotify

 


snmpConfig --show mibCapability
FE-MIB: YES
SW-MIB: YES
FA-MIB: YES
FICON-MIB: YES
HA-MIB: YES
FCIP-MIB: YES
IF-MIB: YES
BD-MIB: YES
BROCADE-MAPS-MIB: YES
T11-FC-ZONE-SERVER-MIB: NO
SW-TRAP: YES
swFCPortScn: YES
swEventTrap: YES
DesiredSeverity:None
swIPv6ChangeTrap: YES
swPmgrEventTrap: YES
swFabricReconfigTrap: NO
swFabricSegmentTrap: NO
swExtTrap: NO
swStateChangeTrap: NO
swPortMoveTrap: NO
swBrcdGenericTrap: NO
swDeviceStatusTrap: NO
swZoneConfigChangeTrap: NO
FA-TRAP: YES
connUnitStatusChange: YES
connUnitEventTrap: YES
connUnitPortStatusChange: YES
FICON-TRAP: YES
linkRNIDDeviceRegistration: YES
linkRNIDDeviceDeRegistration: YES
linkLIRRListenerAdded: YES
linkLIRRListenerRemoved: YES
linkRLIRFailureIncident: YES
HA-TRAP: YES
fruStatusChanged: YES
cpStatusChanged: YES
fruHistoryTrap: YES
IF-TRAP: YES
linkDown: YES
linkUp: YES
BD-TRAP: YES
bdTrap: YES
bdClearTrap: YES
MAPS-TRAP: YES
mapsTrapAM: YES
T11-FC-ZONE-SERVER-TRAP: NO
t11ZsRequestRejectNotify: NO
t11ZsMergeFailureNotify: NO
t11ZsMergeSuccessNotify: NO
t11ZsDefZoneChangeNotify: NO
t11ZsActivateNotify: NO

Occasional Contributor
Posts: 9
Registered: ‎11-30-2017

Re: snmpwalk is giving error No Such Object available on this agent at this OID

[ Edited ]

Just wanted to add one more point ,

 

Looks like  am getting this error when I use OID: .1.3.6.1.3.94

 

The snmpwalk  is responding when I use different OID. 

 

snmpwalk -v 3 -l noAuthNoPriv -u snmpuser1 xx.xx.xx.xx  1.3.6.1.2.1.1  -O n

.1.3.6.1.2.1.1.1.0 = STRING: Fibre Channel Switch.

.1.3.6.1.2.1.1.2.0 = OID: .1.3.6.1.4.1.1588.2.1.1.62

.1.3.6.1.2.1.1.3.0 = Timeticks: (131689800) 15 days, 5:48:18.00

.1.3.6.1.2.1.1.4.0 = STRING: Field Support.

.1.3.6.1.2.1.1.5.0 = STRING: XXXXX

.1.3.6.1.2.1.1.6.0 = STRING: End User Premise.

.1.3.6.1.2.1.1.7.0 = INTEGER: 79

 

 

 

/usr/bin/snmpwalk -v 3 -l noAuthNoPriv -u snmpuser1 xx.xx.xx.xx 1.3.6.1.4.1.1588.2.1.1.50.2 -O n
.1.3.6.1.4.1.1588.2.1.1.50.2.1.0 = INTEGER: 0
.1.3.6.1.4.1.1588.2.1.1.50.2.3.0 = INTEGER: 1
.1.3.6.1.4.1.1588.2.1.1.50.2.4.1.1.1 = INTEGER: 1
.1.3.6.1.4.1.1588.2.1.1.50.2.4.1.2.1 = Hex-STRING: 10 00 00 05 1E 91 D6 00
.1.3.6.1.4.1.1588.2.1.1.50.2.4.1.3.1 = Hex-STRING: 00
.1.3.6.1.4.1.1588.2.1.1.50.2.4.1.4.1 = STRING: "002499"
.1.3.6.1.4.1.1588.2.1.1.50.2.4.1.5.1 = STRING: "384"
.1.3.6.1.4.1.1588.2.1.1.50.2.4.1.6.1 = STRING: "IBM"
.1.3.6.1.4.1.1588.2.1.1.50.2.4.1.7.1 = STRING: "CA"
.1.3.6.1.4.1.1588.2.1.1.50.2.4.1.8.1 = STRING: "00000106425G"
.1.3.6.1.4.1.1588.2.1.1.50.2.4.1.9.1 = Hex-STRING: 15 FF
.1.3.6.1.4.1.1588.2.1.1.50.2.4.1.10.1 = Hex-STRING: 20 0A 00

Occasional Contributor
Posts: 9
Registered: ‎11-30-2017

Re: snmpwalk is giving error No Such Object available on this agent at this OID

Folks 

 

Anyone came accross this type of issue ?

Broadcom Moderator
Posts: 70
Registered: ‎03-29-2010

Re: snmpwalk is giving error No Such Object available on this agent at this OID

It would appear that the MIB reference OID you specified is now depricated in FOS 7.4.x.

 

From the MIB reference for 7.0.x:

 

-
fcmgmt
-
connSet
- uNumber 1.3.6.1.3.94.1.1
- systemURL 1.3.6.1.3.94.1.2
+ connUnitTable 1.3.6.1.3.94.1.6
+ connUnitRevsTable 1.3.6.1.3.94.1.7
+ connUnitSensorTable 1.3.6.1.3.94.1.8
+ connUnitPortTable 1.3.6.1.3.94.1.10
+ connUnitEventTable 1.3.6.1.3.94.1.11
+ connUnitLinkTable 1.3.6.1.3.94.1.12
-
trapReg
- trapMaxClients 1.3.6.1.3.94.2.1
- trapClientCount 1.3.6.1.3.94.2.2
+ trapRegTable 1.3.6.1.3.94.2.3
- revisionNumber 1.3.6.1.3.94.3
- statSet
+ connUnitPortStatTable 1.3.6.1.3.94.4.5
- connUnitServiceSet
+ connUnitServiceScalars 1.3.6.1.3.94.5.1
+ connUnitServiceTables 1.3.6.1.3.94.5.2
~~~~~~~~~~~~~~~~~~ ad-infinitum
 
From the MIB reference for 7.4.x:
 
Search results: 1.3.6.1.3.94
 
No results found
 
However, you can go here: www.mibdepot.com, and find the ones you are looking for. If it's important. 
 
 
doc

Any and all information provided by me is for entertainment value and should not be relied upon as a guaranteed solution or warranty of mechantability. All systems and all networks are different and unique. If you have a concern about data loss, or network disconnection, please open a TAC service request for service through Brocade, or through your OEM equipment provider. If this provided you with a solution to this issue, Please mark it with the button at the bottom "Accept as solution".

Occasional Contributor
Posts: 9
Registered: ‎11-30-2017

Re: snmpwalk is giving error No Such Object available on this agent at this OID

 

Are you sure about that  ?

We have may switches which is running on FOS 7.4.x which is working  and responding to OID 1.3.6.1.3.94.xx.

 

Also, please find the attached image, it says  these are supported 

 

 

 

Broadcom Moderator
Posts: 70
Registered: ‎03-29-2010

Re: snmpwalk is giving error No Such Object available on this agent at this OID

Nope, I'm not sure of anything but death and taxes.

 

Check the FW version of the switches you are running which support that OID. That reference pic is for 7.4.0, and the version on the switch in question is 7.4.1d. If you find a switch with 7.4.1d and the snmpwalk recognizes that string, then you've possibly added a service/maint package which loads that OID(or group of OIDs). The message from FOS is clear enough: "No Such Object available on this agent at this OID" and it is not an error code, it is an informational message. 

doc

Any and all information provided by me is for entertainment value and should not be relied upon as a guaranteed solution or warranty of mechantability. All systems and all networks are different and unique. If you have a concern about data loss, or network disconnection, please open a TAC service request for service through Brocade, or through your OEM equipment provider. If this provided you with a solution to this issue, Please mark it with the button at the bottom "Accept as solution".

Occasional Contributor
Posts: 9
Registered: ‎11-30-2017

Re: snmpwalk is giving error No Such Object available on this agent at this OID

Doc,

 

We have many switches which is running on v7.4.1d and  responding to OID 1.3.6.1.3.94. so I dont think the firmware version is not a problem here. 

 

:(  

Occasional Contributor
Posts: 9
Registered: ‎11-30-2017

Re: snmpwalk is giving error No Such Object available on this agent at this OID

Hello Doc, 

 

Could you please  explain more about this. 

 

 If you find a switch with 7.4.1d and the snmpwalk recognizes that string, then you've possibly added a service/maint package which loads that OID(or group of OIDs).

 

 

I can find the switch with runs on 7.4.1 and its responding to the same OID.  Can you  let me know how we can  add a service /mgmt  package that loads the OID. 

Highlighted
Broadcom Moderator
Posts: 455
Registered: ‎03-29-2011

Re: snmpwalk is giving error No Such Object available on this agent at this OID

Hi,

 

do you have virtual fabric enabled on the switch which fails a walk from OID 1.3.6.1.3.94? Do you have ports in the base switch (128)?

 

If yes, then try the following 

 

snmpwalk -n "VF:<FID for a switch>" -v 3 -l noAuthNoPriv -u snmpuser1 xx.xx.xx.xx 1.3.6.1.3.94 -O n




If this provided you with a solution to this issue, please mark it with the button at the bottom "Accept as solution".


Any and all information provided by me is not reviewed, approved or endorsed by Brocade and is provided solely as a convenience for Brocade customers. All systems and all networks are different and unique. If you have a service affecting network problem, please open a TAC service request for service through Brocade, or through your OEM equipment provider. If this provided you with a solution to this issue, please mark it with the button at the bottom "Accept as solution"
Occasional Contributor
Posts: 9
Registered: ‎11-30-2017

Re: snmpwalk is giving error No Such Object available on this agent at this OID

We dont have the  VF enabled on the failing switches. 

fosconfig --show
FC Routing service: disabled
Virtual Fabric: disabled
Ethernet Switch Service: disabled

Join the Community

Get quick and easy access to valuable resource designed to help you manage your Brocade Network.

vADC is now Pulse Secure
Download FREE NVMe eBook