06-26-2013 01:16 AM
we are now seeing new kind of messages in errdumpall on the switches recently upgraded to FOS 7.1.0c:
2013/06/25-19:59:14:860530, , 1972/0, SLOT 7 | CHASSIS, ERROR, Brocade_DCX, Invalid handle. Handle: 10034870, OID:0x003e0007, glog.c, line: 410, comp:softupgrade, ltime:2013/06/25-19:59:13:502727
2013/06/25-19:59:15:160196, , 1973/0, SLOT 7 | CHASSIS, ERROR, Brocade_DCX, Initialization error. Error: Dest init failure errno=12, OID:0x003e0007, glog.c, line: 181, comp:TRACE CLI, ltime:2013/06/25-19:59:13:802614
2013/06/25-20:01:34:803292, , 1977/0, SLOT 6 | CHASSIS, ERROR, Brocade_DCX, Invalid handle. Handle: 10034870, glog.c, line: 410, comp:softupgrade, ltime:2013/06/25-20:01:34:802902
2013/06/25-20:01:35:209696, , 1978/0, SLOT 6 | CHASSIS, ERROR, Brocade_DCX, Invalid handle. Handle: 100319f8, glog.c, line: 410, comp:TRACE CLI, ltime:2013/06/25-20:01:35:209628
anybody already knows the meaning of these? thanks in advance...
04-22-2014 04:53 AM
Could you please advice on the GLOG errors requested by Alex.
I could also notice the same errors "[GLOG-5002] and [GLOG-5001] error code after upgrading to FOS 7.1.1c on DCX-4S, also notice the IPC-5023 errors.
Awaiting for your prompt reply...
05-08-2014 02:21 AM
Brocade FAQ4146 provides a response to those events:
GLOGmessages are appearing in the
ras logafter a firmware upgrade, switch reboot, power cycle or while taking a
2014/03/19-16:10:35:990962, [GLOG-5001], 1981/0, SLOT 7 | CHASSIS, ERROR,
IBM_2499_384, Initialization error. Error: Dest init failure errno=12,
OID:0x003e0007, glog.c, line: 181, comp:TRACE CLI,
2014/03/19-16:11:39:113543, [GLOG-5002], 1984/0, SLOT 6 | CHASSIS, ERROR,
IBM_2499_384, Invalid handle. Handle: 10034870, glog.c, line: 410,
closed streamwhen dumping log data.
error logand the stream was then closed, the system then attempts to close that stream again but fails and the error is generated. This error has no impact on the switch.
These documents are provided "as is" and without any warranty of any kind, expressed or implied, including, without limitation, any warranty of non-infringement, merchantability, or fitness for a particular purpose. All warranties are expressly disclaimed. User assumes the full risk of using these instructions. In no event shall Brocade be liable for any actual, direct, indirect, punitive, or consequential damages arising from such use, even if advised of the possibility of such damages.
So I wouldn't worry about 'em.
05-15-2014 06:54 AM
Thank you for assisting on this one,
I still have a query, The GLOG error message only seems to occur when we tigger a supportsave is this expected behaviour?
We have only been getting this error since the switch upgraded to 7.1.1c. Is this a known issue on this FW revision?
Do we have any latest firmware revision in which these errors have been fixed.?
Awaiting for your valuable reply.