Fibre Channel (SAN)

Reply
New Contributor
Posts: 2
Registered: ‎09-17-2014

Brocade 300 No Boot

[ Edited ]

Hello,

 

We have a Brocade 300 blade switch that won't boot. All LED's are red.

This is after a chassis shutdown.

 

When we look at the bootup we get this:

 

The system is coming up, please wait...


U-Boot 1.1.3 (May  4 2014 - 20:14:34)

CPU:   AMCC PowerPC 440EPx Rev. A at 660 MHz (PLB=165, OPB=82, EBC=41 MHz)
       No Security/Kasumi support
       I2C boot EEPROM enabled
       Bootstrap Option G - Boot ROM Location I2C (Addr 0x54)
       Internal PCI arbiter enabled, PCI async ext clock used
       32 kB I-Cache 32 kB D-Cache
Board: Bulova
I2C:   ready
DRAM:  Initializing DDRSDRAM
DDR Init: speed = 165000002
DQS calibration - Window detected:
max_passing_cases = 50
wr_dqs_shift      = 95
dll_dqs_delay_X   = 29
dll_dqs_delay_X window = 5 - 54
DDR0_09=0x00011d5f
DDR0_22=0x00267f0b
DDR0_17=0x1d004900
DDR0_18=0x1d1d1d1d
DDR0_19=0x1d1d1d1d
ECC Enabling   DONE
512 MB
POST RAM test disabled.
Now running in RAM - U-Boot at: 1fb2b000
trap_init : 0x0
system inventory subsystem initialized
FLASH: Bulova CFI Flash Driver Initialized
 4 MB
ATA interface setup: io_base=0xf8f00000, port=0x3e0, ctl=0x7ec
PCI:
Skip our host bridge
        00  08  1657  0011  0280  18
In:    serial
Out:   serial
Err:   serial
Net:

Checking system RAM - press any key to stop test

Checking memory address: 00100000

System RAM test using Default POST RAM Test succeeded.

set_bootstatus: BS_LOAD_OS, platform_idx = 2

Type run flash_nfs to mount root filesystem over NFS

Hit ESC to stop autoboot:  0
Map file at LBA sector 0x85e20
Bad Data CRCATA()85e20 checksum: 0x8e943822
Embbeded checksum: 0x340ede3c
Map file at LBA sector 0x1403f
## Booting image at 00400000 ...
   Image Name:   Linux-2.6.14.2
   Image Type:   PowerPC Linux Multi-File Image (uncompressed)
   Data Size:    4290075 Bytes =  4.1 MB
   Load Address: 00000000
   Entry Point:  00000000
   Contents:
   Image 0:  3211397 Bytes =  3.1 MB
   Image 1:  1078663 Bytes =  1 MB
## Current stack ends at 0x1FAE9BE8 => set upper limit to 0x00C00000
## initrd at 0x007100D4 ... 0x0081765A (len=1078663=0x107587)
   Loading Ramdisk to 1f9e1000, end 1fae8587 ... OK
 initrd_start = 1f9e1000, initrd_end = 1fae8587
## Transferring control to Linux (at address 00000000) ...
Installing Linux 2.6 Kernel
Attempting to find a root file system on hda2...
INIT: version 2.78 booting
Bypassing firmware validation.
INIT: Entering runlevel: 3
/etc/rc.d/rc3.d/S00fipskat: line 137: unexpected EOF while looking for matching `}'
/etc/rc.d/rc3.d/S00fipskat: line 194: syntax error: unexpected end of file
/etc/rc.d/rc3.d/S95fabos: line 2298: unexpected EOF while looking for matching ``'
/etc/rc.d/rc3.d/S95fabos: line 2353: syntax error: unexpected end of file

Fabric OS (SW)

It is impossible to issue any command like supportsave. 

Is there a way to repair this Bad Data CRC?

 

Thank you for your help

External Moderator
Posts: 5,040
Registered: ‎02-23-2004

Re: Brocade 300 No Boot

Tassio,

 

error in boot order, stay indicated a Issue caused by wrong FOS Release, and/or interrupted firmwaredownload.

 

can you please specified both, Release bevore upgrade, and the Release you want to install ?

 

 

Installing Linux 2.6 Kernel
Attempting to find a root file system on hda2...
TechHelp24
New Contributor
Posts: 2
Registered: ‎09-17-2014

Re: Brocade 300 No Boot

Techhelp24,

 

Thanks for your help.

This occurred after a power cycle, not a firmware update.

The switch was operating ok before the power cycle.

Do you know a way to repair the fabric OS?

 

Tussio

External Moderator
Posts: 5,040
Registered: ‎02-23-2004

Re: Brocade 300 No Boot

If a Partion is corrupted or Compact Flash defective, there is no way to recovery or re-install the FOS, or replace teh Compact Flash.

 

in such case you must open a call with the Support for replacement with you Vendor / OEM if the Switch is under maintenance.

TechHelp24

Join the Community

Get quick and easy access to valuable resource designed to help you manage your Brocade Network.

vADC is now Pulse Secure
Download FREE NVMe eBook