Fibre Channel (SAN)

Reply
New Contributor
Posts: 4
Registered: ‎09-03-2015

6510 failing to boot

Hi

 

I've got a 6510 which looks as though it has corrupt firmware.

It's constantly rebooting, and when you can log in, no FOS commands will run.

Is it possible to reflash ?

 

I can get in to the preboot menu ok.

 

Cheers,

Rob

 

MORD6510_A console login: 2015/09/03-18:50:15, [HAM-1007], 30563, FFDC | CHASSIS, CRITICAL, Brocade6510, Need to reboot the system for recovery, reason: Softt
2015/09/03-18:50:15, [RAS-1001], 30564, CHASSIS, INFO, Brocade6510, First failure data capture (FFDC) event occurred.
cat: /var/log/fsslo.log: No such file or directory
2015/09/03-18:50:45, [HAM-1008], 30565, FFDC | CHASSIS, CRITICAL, Brocade6510, Rebooting the system for recovery - auto-reboot is enabled
2015/09/03-18:50:45, [RAS-1001], 30566, CHASSIS, INFO, Brocade6510, First failure data capture (FFDC) event occurred.
Restarting system.

The system is coming up, please wait...


U-Boot 1.1.3 (May 29 2011 - 20:03:39)

CPU: AMCC PowerPC 440EPx Rev. A at 660 MHz (PLB=132, OPB=66, EBC=33 MHz)
No Security/Kasumi support
I2C boot EEPROM enabled
Bootstrap Option G - Boot ROM Location I2C (Addr 0x54)
Internal PCI arbiter enabled, PCI async ext clock used
32 kB I-Cache 32 kB D-Cache
Board: Stinger
I2C: ready
DRAM: Initializing DDRSDRAM
DQS calibration - Window detected:
max_passing_cases = 55
wr_dqs_shift = 90
dll_dqs_delay_X = 30
dll_dqs_delay_X window = 3 - 57
DDR0_09=0x00011d5a
DDR0_22=0x03267a0b
DDR0_17=0x1e006300
DDR0_18=0x1e1e1e1e
DDR0_19=0x1e1e1e1e
Zeroing SDRAM... DONE
DDR: 1024 MB
POST RAM test disabled.
Now running in RAM - U-Boot at: 3fb30000
trap_init : 0x0
system inventory subsystem initialized
FLASH: Stinger CFI Flash Driver Initialized
4 MB

DEBUG: ASIC Reset Enable Register Offset:0x88 Value:0x03...

CPLD: Reseting Bridge & ASIC...
ATA interface setup: io_base=0xf8f00000, port=0x3e0, ctl=0x7ec
PCI:
Skip our host bridge
01 00 1657 001d 0280 1a
00 07 10b5 8112 0604 18
In: serial
Out: serial
Err: serial
Net:

Checking system RAM - press any key to stop test

Checking memory address: 00100000

System RAM test using Default POST RAM Test succeeded.

set_bootstatus: BS_LOAD_OS, platform_idx = 14

Type run flash_nfs to mount root filesystem over NFS

Hit ESC to stop autoboot: 0
Map file at LBA sector 0x113388
## Booting image at 00400000 ...
Image Name: Linux-2.6.14.2
Image Type: PowerPC Linux Multi-File Image (uncompressed)
Data Size: 4269595 Bytes = 4.1 MB
Load Address: 00000000
Entry Point: 00000000
Contents:
Image 0: 3190918 Bytes = 3 MB
Image 1: 1078663 Bytes = 1 MB
## Current stack ends at 0x3FAEEBE8 => set upper limit to 0x00C00000
## initrd at 0x0070B0D4 ... 0x0081265A (len=1078663=0x107587)
Loading Ramdisk to 1fef8000, end 1ffff587 ... OK
initrd_start = 1fef8000, initrd_end = 1ffff587
## Transferring control to Linux (at address 00000000) ...
Installing Linux 2.6 Kernel
Attempting to find a root file system on hda2...
INIT: version 2.78 booting
Bypassing firmware validation.
INIT: Entering runlevel: 3
Starting Fabric OS Services...
FIPS off, RRD...
Found 4(threshold 5) abnormal reboots within 3000 seconds window(threshold)
rscmon_service: started thread!
rscmon_service: started thread!
sys_chip_init: class 0 max 24 Done
ethsw_ha_enabled = 1
uptime: 4293889222; sup_qid: 0
.


Fabric OS (MORD6510_A)


MORD6510_A console login: 2015/09/03-18:51:26, [HAM-1004], 30567, CHASSIS, INFO, Brocade6510, Processor rebooted - Software Bootup Failure:Bringup timed out

SNMP Research EMANATE/Lite Agent Version 16.2.0.9
Copyright 1989-2006 SNMP Research, Inc.


If your terminal supports lower case letters, please
use them. Login again, using lower case if possible.


MORD6510_A console login: 2015/09/03-18:53:44, [HAM-1007], 30568, FFDC | CHASSIS, CRITICAL, Brocade6510, Need to reboot the system for recovery, reason: Softt
2015/09/03-18:53:44, [RAS-1001], 30569, CHASSIS, INFO, Brocade6510, First failure data capture (FFDC) event occurred.
cat: /var/log/fsslo.log: No such file or directory
admin
Password:
WARNING! This system is blah blah blah blah blah

-----------------------------------------------------------------

Please change passwords for switch default accounts now.
Use Control-C to exit or press 'Enter' key to proceed.
Warning: Access to the Root and Factory accounts may be required for
proper support of the switch. Please ensure the Root and Factory
passwords are documented in a secure location. Recovery of a lost Root
or Factory password will result in fabric downtime.

for user - root
Changing password for root
Enter new password:
Password was not changed. Will prompt again at next login
until password is changed.
MORD6510_A:FID128:admin>
MORD6510_A:FID128:admin> switchshow
rbash: switchshow: command not found
MORD6510_A:FID128:admin> 2015/09/03-18:54:14, [HAM-1008], 30570, FFDC | CHASSIS, CRITICAL, Brocade6510, Rebooting the system for recovery - auto-reboot is end
2015/09/03-18:54:14, [RAS-1001], 30571, CHASSIS, INFO, Brocade6510, First failure data capture (FFDC) event occurred.

MORD6510_A:FID128:admin> errsRestarting system.

 

 

-----------------------------------------------------------------
**************************************************************
* *
* Fabric OS has detected frequent switch reboot condition. *
* Following actions can be taken to recover the switch: *
* - remove or replace any problem blades (if applicable to *
* platform). *
* - use supportsave to collect supportsave data. *
* *
**************************************************************
sysmodAttach open failed: No such device or address
fabsys device open: No such device or address
Raslog Module Initialisation failed rc=-1
fabsys device open: No such device or address

 

 

Join the Community

Get quick and easy access to valuable resource designed to help you manage your Brocade Network.

vADC is now Pulse Secure
Download FREE NVMe eBook