For more details, please see ourCookie Policy.


Fibre Channel (SAN)

Reply
Occasional Contributor
Posts: 6
Registered: ‎05-15-2018
Accepted Solution

Password Break Mechanism

Help Required !!!!!!!!!!!!!!!!!!!!!!!!!!!!!

 

I want DS5100b Switch Password break Mechnisim as I forgot the Old one. Thanks in advance. 

Frequent Contributor
Posts: 83
Registered: ‎04-04-2018

Re: Password Break Mechanism

[ Edited ]

Hello,

 

do you know root password or you totaly forgotten all passwords?

Which FOS version you are running ?

Please mark this response as "Accept as Solution" if it answers your question.

Marian Bezeg
Occasional Contributor
Posts: 6
Registered: ‎05-15-2018

Re: Password Break Mechanism

Thanks for Response !!!!!

 

I Dont know any Password including Root . As I m New User to Brocade . I dont know how to check FOS version

 

Kindly find FOS version below. 

 

-----------------------------------------------------------------------------------------------------------------------------

 

The system is coming up, please wait...


U-Boot 1.1.3 (Nov 8 2010 - 17:35:35)

CPU: AMCC PowerPC 440EPx Rev. A at 660 MHz (PLB=132, OPB=66, EBC=33 MHz)
No Security/Kasumi support
I2C boot EEPROM enabled
Bootstrap Option G - Boot ROM Location I2C (Addr 0x54)
Internal PCI arbiter enabled, PCI async ext clock used
32 kB I-Cache 32 kB D-Cache
Board: Spirit
I2C: ready
DRAM: Initializing DDRSDRAM
DDR Init: speed = 132000002
DQS calibration - Window detected:
max_passing_cases = 53
wr_dqs_shift = 95
dll_dqs_delay_X = 30
dll_dqs_delay_X window = 4 - 56
DDR0_09=0x00011d5f
DDR0_22=0x00267f0b
DDR0_17=0x1e005d00
DDR0_18=0x1e1e1e1e
DDR0_19=0x1e1e1e1e
ECC Enabling DONE
512 MB
POST RAM test disabled.
Now running in RAM - U-Boot at: 1fb31000
trap_init : 0x0
system inventory subsystem initialized
FLASH: Spirit CFI Flash Driver Initialized
4 MB
ATA interface setup: io_base=0xf8f00000, port=0x1f0, ctl=0x3f6
PCI:
Skip our host bridge
00 07 1657 0010 0280 18
In: serial
Out: serial
Err: serial
Net:

Checking system RAM - press any key to stop test

Checking memory address: 00100000

System RAM test terminated by keyboard
set_bootstatus: BS_LOAD_OS, platform_idx = 3

Type run flash_nfs to mount root filesystem over NFS

Hit ESC to stop autoboot: 0

1) Start system.
2) Recover password.
3) Enter command shell.

Option?

) Start system.
2) Recover password.
3) Enter command shell.

Option? 3
Passw
The system is coming up, please wait...


U-Boot 1.1.3 (Nov 8 2010 - 17:35:35)

CPU: AMCC PowerPC 440EPx Rev. A at 660 MHz (PLB=132, OPB=66, EBC=33 MHz)
No Security/Kasumi support
I2C boot EEPROM enabled
Bootstrap Option G - Boot ROM Location I2C (Addr 0x54)
Internal PCI arbiter enabled, PCI async ext clock used
32 kB I-Cache 32 kB D-Cache
Board: Spirit
I2C: ready
DRAM: Initializing DDRSDRAM
DDR Init: speed = 132000002
DQS calibration - Window detected:
max_passing_cases = 53
wr_dqs_shift = 95
dll_dqs_delay_X = 30
dll_dqs_delay_X window = 4 - 56
DDR0_09=0x00011d5f
DDR0_22=0x00267f0b
DDR0_17=0x1e005d00
DDR0_18=0x1e1e1e1e
DDR0_19=0x1e1e1e1e
ECC Enabling DONE
512 MB
POST RAM test disabled.
Now running in RAM - U-Boot at: 1fb31000
trap_init : 0x0
system inventory subsystem initialized
FLASH: Spirit CFI Flash Driver Initialized
4 MB
ATA interface setup: io_base=0xf8f00000, port=0x1f0, ctl=0x3f6
PCI:
Skip our host bridge
00 07 1657 0010 0280 18
In: serial
Out: serial
Err: serial
Net:

Checking system RAM - press any key to stop test

Checking memory address: 00100000

System RAM test terminated by keyboard
set_bootstatus: BS_LOAD_OS, platform_idx = 3

Type run flash_nfs to mount root filesystem over NFS

Hit ESC to stop autoboot: 0

1) Start system.
2) Recover password.
3) Enter command shell.

Option?

) Start system.
2) Recover password.
3) Enter command shell.

Option? 3
Password:

Invalid Password. Retry
Password:

Invalid Password. Retry
Password:

Invalid Password. Retry

Authentication failure. Booting in normal mode.
Map file at LBA sector 0x9c0f7
## Booting image at 00400000 ...
Image Name: Linux-2.6.14.2
Image Type: PowerPC Linux Multi-File Image (uncompressed)
Data Size: 4267435 Bytes = 4.1 MB
Load Address: 00000000
Entry Point: 00000000
Contents:
Image 0: 3190918 Bytes = 3 MB
Image 1: 1076503 Bytes = 1 MB
## Current stack ends at 0x1FAEFBE0 => set upper limit to 0x00C00000
## initrd at 0x0070B0D4 ... 0x00811DEA (len=1076503=0x106D17)
Loading Ramdisk to 1f9e8000, end 1faeed17 ... OK
initrd_start = 1f9e8000, initrd_end = 1faeed17
## Transferring control to Linux (at address 00000000) ...
Installing Linux 2.6 Kernel
Attempting to find a root file system on hda1...
INIT: version 2.78 booting
Bypassing firmware validation.
INIT: Entering runlevel: 3
Starting Fabric OS Services...
sys_chip_init: class 0 max 24 Done
ethsw_ha_enabled = 1
uptime: 4293889213; sup_qid: 0
2018/05/16-04:13:37, [HAM-1004], 3076, CHASSIS, INFO, DS_5100B, Processor reboot ed - Unknown
.

 

Fabric OS (StorageSwitch1)


StorageSwitch1 console login: SNMP Research EMANATE/Lite Agent Version 16.2.0.9
Copyright 1989-2006 SNMP Research, Inc.
ki_state_set: redundant ACTIVATE for instance 1
2018/05/16-04:13:56, [FCR-1069], 3077, FID 128, INFO, StorageSwitch1, The FC Rou ting service is enabled.
2018/05/16-04:13:56, [LOG-1000], 3078, FID 128, INFO, StorageSwitch1, Previous m essage repeated 1 time(s)
2018/05/16-04:14:05, [ZONE-1022], 3079, FID 128, INFO, StorageSwitch1, The effec tive configuration has changed to IBAConfig.
All service instances on Active
POST1: Started running Wed May 16 04:14:09 GMT 2018
POST1: Test #1 - Running turboramtest
2018/05/16-04:14:10, [EM-1034], 3080, CHASSIS, ERROR, DS_5100B, PS 2 set to faul ty, rc=2000e.
2018/05/16-04:14:10, [LOG-1000], 3084, CHASSIS, INFO, DS_5100B, Previous message repeated 4 time(s)
POST1: Script PASSED with exit status of 0 Wed May 16 04:14:11 GMT 2018 took (0: 0:2)
POST2: Started running Wed May 16 04:14:12 GMT 2018
2018/05/16-04:14:13, [HIL-1610], 3085, CHASSIS, WARNING, DS_5100B, Fan/PS unit 2 not supplying power, fan speeds not available. Please ensure that the unit has power and the switch is on.
POST2: Test #1 - Running portloopbacktest (SERDES)
POST2: Running diagshow
POST2: Script PASSED with exit status of 0 Wed May 16 04:14:20 GMT 2018 took (0: 0:8)
2018/05/16-04:14:22, [BL-1000], 3086, CHASSIS, INFO, DS_5100B, Initializing port s...
2018/05/16-04:14:22, [BL-1001], 3087, CHASSIS, INFO, DS_5100B, Port initializati on completed.
2018/05/16-04:14:44, [FW-1010], 3088, FID 128, WARNING, StorageSwitch1, Env Powe r Supply 2, is below low boundary(High=0, Low=1). Current value is 0 (1 OK/0 FAU LTY).
2018/05/16-04:15:08, [FW-1424], 3089, FID 128, WARNING, StorageSwitch1, Switch s tatus changed from HEALTHY to DOWN.
2018/05/16-04:15:08, [FW-1427], 3090, FID 128, WARNING, StorageSwitch1, Switch s tatus change contributing factor Power supply: 1 bad.
2018/05/16-04:15:08, [FW-1431], 3091, FID 128, WARNING, StorageSwitch1, Switch s tatus change contributing factor Fan: 1 bad.

Frequent Contributor
Posts: 83
Registered: ‎04-04-2018

Re: Password Break Mechanism

Hello,

 

try to folow pages 8 and 9.

 

http://www.cagedrat.com/wp-content/uploads/2016/03/FOS_Password_Recovery_Notes.pdf

Please mark this response as "Accept as Solution" if it answers your question.

Marian Bezeg
Occasional Contributor
Posts: 6
Registered: ‎05-15-2018

Re: Password Break Mechanism

As I am going through the samne process as PDF but It is asking Passsword !!!!!

 

Checking system RAM - press any key to stop test

Checking memory address: 00100000

System RAM test terminated by keyboard
set_bootstatus: BS_LOAD_OS, platform_idx = 3

Type run flash_nfs to mount root filesystem over NFS

Hit ESC to stop autoboot: 0

1) Start system.
2) Recover password.
3) Enter command shell.

Option?

) Start system.
2) Recover password.
3) Enter command shell.

Option? 3
Password:

Occasional Contributor
Posts: 6
Registered: ‎05-15-2018

Re: Password Break Mechanism

Dear Marian Bezeg,

 

If its feasible for you I can Provide you Teamviwer or anydesk Session . You can have look . 

Frequent Contributor
Posts: 83
Registered: ‎04-04-2018

Re: Password Break Mechanism

Hello,

 

This prompt which you get is for Boot PROM password. 

If you loose this password as well there is no way to recovery it without assistence of Brocade Support.

 

The process is described on page 8.

 

https://community.brocade.com/dtscp75322/attachments/dtscp75322/fibre/25305/1/53_1000114_02_FOS_Password_Recovery.pdf

 

I'm sorry but i cant help you with this problem more and without Brocade support you will be not able to access switch anymore.

Please mark this response as "Accept as Solution" if it answers your question.

Marian Bezeg
Occasional Contributor
Posts: 6
Registered: ‎05-15-2018

Re: Password Break Mechanism

Kindly  Send Support Email ID and Thanks Alot for your Help !!!!!!!!!!!!!!!!!

Join the Community

Get quick and easy access to valuable resource designed to help you manage your Brocade Network.