09-17-2014 04:55 AM - edited 09-17-2014 04:57 AM
We have a Brocade 300 blade switch that won't boot. All LED's are red.
This is after a chassis shutdown.
When we look at the bootup we get this:
The system is coming up, please wait... U-Boot 1.1.3 (May 4 2014 - 20:14:34) CPU: AMCC PowerPC 440EPx Rev. A at 660 MHz (PLB=165, OPB=82, EBC=41 MHz) No Security/Kasumi support I2C boot EEPROM enabled Bootstrap Option G - Boot ROM Location I2C (Addr 0x54) Internal PCI arbiter enabled, PCI async ext clock used 32 kB I-Cache 32 kB D-Cache Board: Bulova I2C: ready DRAM: Initializing DDRSDRAM DDR Init: speed = 165000002 DQS calibration - Window detected: max_passing_cases = 50 wr_dqs_shift = 95 dll_dqs_delay_X = 29 dll_dqs_delay_X window = 5 - 54 DDR0_09=0x00011d5f DDR0_22=0x00267f0b DDR0_17=0x1d004900 DDR0_18=0x1d1d1d1d DDR0_19=0x1d1d1d1d ECC Enabling DONE 512 MB POST RAM test disabled. Now running in RAM - U-Boot at: 1fb2b000 trap_init : 0x0 system inventory subsystem initialized FLASH: Bulova CFI Flash Driver Initialized 4 MB ATA interface setup: io_base=0xf8f00000, port=0x3e0, ctl=0x7ec PCI: Skip our host bridge 00 08 1657 0011 0280 18 In: serial Out: serial Err: serial Net: Checking system RAM - press any key to stop test Checking memory address: 00100000 System RAM test using Default POST RAM Test succeeded. set_bootstatus: BS_LOAD_OS, platform_idx = 2 Type run flash_nfs to mount root filesystem over NFS Hit ESC to stop autoboot: 0 Map file at LBA sector 0x85e20 Bad Data CRCATA()85e20 checksum: 0x8e943822 Embbeded checksum: 0x340ede3c Map file at LBA sector 0x1403f ## Booting image at 00400000 ... Image Name: Linux-22.214.171.124 Image Type: PowerPC Linux Multi-File Image (uncompressed) Data Size: 4290075 Bytes = 4.1 MB Load Address: 00000000 Entry Point: 00000000 Contents: Image 0: 3211397 Bytes = 3.1 MB Image 1: 1078663 Bytes = 1 MB ## Current stack ends at 0x1FAE9BE8 => set upper limit to 0x00C00000 ## initrd at 0x007100D4 ... 0x0081765A (len=1078663=0x107587) Loading Ramdisk to 1f9e1000, end 1fae8587 ... OK initrd_start = 1f9e1000, initrd_end = 1fae8587 ## Transferring control to Linux (at address 00000000) ... Installing Linux 2.6 Kernel Attempting to find a root file system on hda2... INIT: version 2.78 booting Bypassing firmware validation. INIT: Entering runlevel: 3 /etc/rc.d/rc3.d/S00fipskat: line 137: unexpected EOF while looking for matching `}' /etc/rc.d/rc3.d/S00fipskat: line 194: syntax error: unexpected end of file /etc/rc.d/rc3.d/S95fabos: line 2298: unexpected EOF while looking for matching ``' /etc/rc.d/rc3.d/S95fabos: line 2353: syntax error: unexpected end of file Fabric OS (SW)
It is impossible to issue any command like supportsave.
Is there a way to repair this Bad Data CRC?
Thank you for your help
09-17-2014 09:57 AM
error in boot order, stay indicated a Issue caused by wrong FOS Release, and/or interrupted firmwaredownload.
can you please specified both, Release bevore upgrade, and the Release you want to install ?
Installing Linux 2.6 Kernel Attempting to find a root file system on hda2...
09-18-2014 11:39 PM
Thanks for your help.
This occurred after a power cycle, not a firmware update.
The switch was operating ok before the power cycle.
Do you know a way to repair the fabric OS?
09-22-2014 08:54 PM
If a Partion is corrupted or Compact Flash defective, there is no way to recovery or re-install the FOS, or replace teh Compact Flash.
in such case you must open a call with the Support for replacement with you Vendor / OEM if the Switch is under maintenance.