Ethernet Switches & Routers

Reply
Brocadian
Posts: 9
Registered: ‎06-07-2011

show qd-share-level for ICX 7450

show qd-share-level for ICX 7450
I am able to run this command on an FCX running 7.4 code stream, L2. I requested from one of my customers to run this command from an ICX-7450 running 8.00.20c and provide me the output. He received an invalid input response. Can anyone validate that this is the expected response. I did check the 8.00.20 software manuals and this show command is not documented. Does anyone know how I can get this output? Regards, Regis
John Regis
Brocade LAN SE
Work - 914-302-2947
Contributor
Posts: 37
Registered: ‎02-27-2015

Re: show qd-share-level for ICX 7450

Hi,

 

I'm sharing output of show qd-share-level command of my ICX6450-24p switch running 08.0.20c version.

I know it is not 7450 but it is using the same OS.

 

SSH@partaTeknoloji#show qd-share-level
Sharing level: 1-64KB, 2-250KB (default), 3-375KB, 4-500KB, 5-625KB , 6-750KB, 7-875KB, 8-1000KB
Current qd sharing level 2
Device 0 sharing buffers in use 0

 

SSH@partaTeknoloji#show version
Copyright (c) 1996-2014 Brocade Communications Systems, Inc. All rights reserved.
UNIT 1: compiled on Mar 28 2015 at 04:00:54 labeled as ICX64S08020c
(8314524 bytes) from Secondary ICX64S08020c.bin
SW: Version 08.0.20cT311
Boot-Monitor Image size = 786944, Version:10.1.04T310 (kxz10104)
HW: Stackable ICX6450-24-HPOE
==========================================================================
UNIT 1: SL 1: ICX6450-24p POE 24-port Management Module
Serial #: BZR2517H048
License: BASE_SOFT_PACKAGE (LID: dbtHKGMjFJN)
P-ENGINE 0: type DEF0, rev 01
==========================================================================
UNIT 1: SL 2: ICX6450-SFP-Plus 4port 40G Module
==========================================================================
800 MHz ARM processor ARMv5TE, 400 MHz bus
65536 KB flash memory
512 MB DRAM
STACKID 1 system uptime is 7 days 11 hours 22 minutes 36 seconds
The system : started=cold start

--
Best Regards
Destan YILANCI
Brocadian
Posts: 9
Registered: ‎06-07-2011

Re: show qd-share-level for ICX 7450

Thanks for the reponse. Here is the output from the customers 7450. I need to continue to investigate. i mus tbe missing something. Although when I look at the version info below, "SPS......" this looks unfamiliar to me.

User Access Verification

 

Please Enter Password:

 

User login successful.

 

telnet@ICX7450-48P Switch>en

Password:

telnet@ICX7450-48P Switch#show qd-share-level

Invalid input -> qd-share-level

Type ? for a list

telnet@ICX7450-48P Switch#show ver

  Copyright (c) 1996-2014 Brocade Communications Systems, Inc. All rights reserv

ed.

    UNIT 1: compiled on Dec 18 2014 at 07:14:06 labeled as SPS08020b

      (25238404 bytes) from Secondary SPS08020b.bin

        SW: Version 08.0.20bT211

      Compressed Boot-Monitor Image size = 786944, Version:10.1.04T215 (spz10104

)

  HW: Stackable ICX7450-48-HPOE

  Internal USB: Serial #: 9900614081100384

      Vendor: ATP Electronics, Total size = 1919 MB

==========================================================================

UNIT 1: SL 1: ICX7450-48P POE 48-port Management Module

      Serial  #:CYR3349K04N

      License: BASE_SOFT_PACKAGE   (LID: eatIIJOmFJp)

eatIIJOmFJp)

      P-ASIC  0: type B548, rev 01  Chip BCM56548_A0

==========================================================================

1000 MHz ARM processor ARMv7 88 MHz bus

8192 KB boot flash memory

2048 MB code flash memory

2048 MB DRAM

STACKID 1  system uptime is 15 days 5 hours 10 seconds

The system : started=cold start

 

telnet@ICX7450-48P Switch#

 

John Regis
Brocade LAN SE
Work - 914-302-2947
Occasional Contributor
Posts: 19
Registered: ‎05-23-2013

Re: show qd-share-level for ICX 7450

[ Edited ]

Good morning, jregis. To comment on your SPS comment, looking at the release notes for 08.0.02b the file name for the switching software is SPS08020b.bin for layer 2. It was the first time I had seen it as well.

 

I can't really comment much on your issue as I only have ICX 6610s, but I believe in your initial post you stated that both were running the same version (c). Your customer appears to be on (b) from the show version command you pasted. I doubt it would do anything, but if you really need an exact comparison you could always upgrade him to (c) as well and see if it solves your issue. I did a quick glance at the documentation, and I see nothing, anywhere, that states this functionality is not present in the 7450. I would put in a ticket to Brocade support to see if they have quick fix for this, or if it is possibly a not-so-known issue with this model/release combo.

 

Best of luck to you in solving the issue.

 

EDIT: I couldn't see your original post when replying - I now see you are on different hardware versions. If the upgrade considerations don't prevent you from upgrading him to c, that is still one troubleshooting step you can take to rule out any issues with b on this model, assuming it doesn't interrupt them too much.

Join the Community

Get quick and easy access to valuable resource designed to help you manage your Brocade Network.

Download FREE NVMe eBook