Fibre Channel (SAN)

Reply
Occasional Contributor
Posts: 6
Registered: ‎03-14-2012

spinfab error

hi can anybody explain the error below

link is 2 G using Multiplexer device , i have very slow transfer rate max 17MB/s  and when i run spinfab i got error

DCX-Lower-sw01:admin> spinfab -ports 2/19

Running spinfab ..............

ERROR: DIAG PORTSTOPPED spinfab:spinfab, 0 nMegs,

Pt2/19(66) Ch1/26 No Longer Transmitting, FTX Counter Stuck at 72814901,

Err# 13A012E 0242

spinfab: Completed 11 megs, status:  FAILED.

        port 83 test status: 0x00000002 --  FAILED.

FAILED.

Occasional Contributor
Posts: 6
Registered: ‎03-14-2012

Re: spinfab error

any help

External Moderator
Posts: 4,787
Registered: ‎02-23-2004

Re: spinfab error

--->>>...link is 2 G using Multiplexer device

is the link as xWDM ?

have you tried to Fix the Port Speed at 2G instead AN ?

TechHelp24
Occasional Contributor
Posts: 6
Registered: ‎03-14-2012

Re: spinfab error

Hi here full details

portspeed on both side is N2 ( auto)

we have huawei dwdm fc200 2.125G   fiber link connect two DataCenter , when we issue spinfab we got the below error , kindly advice

DCX-Lower-sw01:admin> spinfab -ports 2/19

Running spinfab ..............

ERROR: DIAG PORTSTOPPED spinfab:spinfab, 0 nMegs,

Pt2/19(66) Ch1/26 No Longer Transmitting, FTX Counter Stuck at 89583125,

Err# 13A012E 0242

spinfab: Completed 11 megs, status:  FAILED.

         port 83 test status: 0x00000002 --  FAILED.

  FAILED.

DCX-Lower-sw01:admin>

kindly note link transfer rate is slow we got as max 16MB/s.

siwtches DS-4900B FOS v5.1.0a

DCX-4S  FOS v6.4.2a

is there any parameter to change on brocade

----------------

fcping  10:00:00:05:1e:04:be:18

Destination:    10:00:00:05:1e:04:be:18

Pinging 10:00:00:05:1e:04:be:18 with 12 bytes of data:

received reply from 10:00:00:05:1e:04:be:18: 12 bytes time:1385 usec

received reply from 10:00:00:05:1e:04:be:18: 12 bytes time:1284 usec

received reply from 10:00:00:05:1e:04:be:18: 12 bytes time:1227 usec

received reply from 10:00:00:05:1e:04:be:18: 12 bytes time:1264 usec

received reply from 10:00:00:05:1e:04:be:18: 12 bytes time:1676 usec

5 frames sent, 5 frames received, 0 frames rejected, 0 frames timeout

Round-trip min/avg/max = 1227/1367/1676 usec

-------------------

DCX-Lower-sw01:admin> islshow

  1: 17-> 23 10:00:00:05:33:5c:98:3a  43 HP_Enc1_sw1     sp:  8.000G bw:  8.000G

  2: 72->  0 10:00:00:05:33:5c:98:3a  43 HP_Enc1_sw1     sp:  8.000G bw:  8.000G

  3: 83-> 44 10:00:00:05:1e:04:be:18   1 Fabric-A        sp:  2.000G bw:  2.000G

--------------

portshow 2/19

portIndex:  83

portName:

portHealth: HEALTHY

Authentication: None

portDisableReason: None

portCFlags: 0x1

portFlags: 0x10004907    PRESENT ACTIVE E_PORT G_PORT LOGICAL_ONLINE LOGIN LED

LocalSwcFlags: 0x0

portType:  17.0

portState: 1    Online

Protocol: FC

portPhys:  6    In_Sync         portScn:   16   E_Port

port generation number:    12098

state transition count:    22

portId:    1b5300

portIfId:    43220802

portWwn:   20:53:00:05:33:25:49:00

portWwn of device(s) connected:

Distance:  normal

portSpeed: N2Gbps

LE domain: 0

FC Fastwrite: OFF

Interrupts:        0          Link_failure: 63         Frjt:         0

Unknown:           0          Loss_of_sync: 22         Fbsy:         0

Lli:               203        Loss_of_sig:  42

Proc_rqrd:         415367     Protocol_err: 0

Timed_out:         0          Invalid_word: 565795

Rx_flushed:        0          Invalid_crc:  0

Tx_unavail:        0          Delim_err:    0

Free_buffer:       0          Address_err:  2

Overrun:           0          Lr_in:        19

Suspended:         0          Lr_out:       13

Parity_err:        0          Ols_in:       3

Suspended:     0      Lr_out:   13
Parity_err:    0      Ols_in:   3
2_parity_err:  0      Ols_out:  36
CMI_bus_err:   0

Port part of other ADs: No

Occasional Contributor
Posts: 6
Registered: ‎03-14-2012

Re: spinfab error

so what do you think

External Moderator
Posts: 4,787
Registered: ‎02-23-2004

Re: spinfab error

--->>>so what do you think

->siwtches DS-4900B FOS v5.1.0a

->DCX-4S  FOS v6.4.2a

->is there any parameter to change on brocade

FOS 6.4.x is not supported with FOS v5.1.x and required a minimum Release of FOS 5.3.2 or higher.

I would first upgarde the FOS.

before you start Upgrade, check compatibility Matrix about Supported Array, HBA and other Connectivity.

TechHelp24
Occasional Contributor
Posts: 6
Registered: ‎03-14-2012

Re: spinfab error

many thanks

can you tell which document say FOS 6.4.x is not supported with FOS v5.1.x

External Moderator
Posts: 4,787
Registered: ‎02-23-2004

Re: spinfab error

See attached Release Notes v6.4.2a

TechHelp24

Join the Community

Get quick and easy access to valuable resource designed to help you manage your Brocade Network.