Fibre Channel (SAN)

Reply
New Contributor
Posts: 2
Registered: ‎03-20-2010

Mcdata 4400 can't startup

Hi

  I reboot Mcdata 4400,it can't startup.I connect to the switch whit a serial cable.I get the same result.

Does anyone know if this is possible to fix.

The version of the Firmware is 08.00.01 2

Initialize CF.... DONE

cf_binfile_check(): MAGIC 0

call boot_dwnld(1)


<< BOOT Area Terminal Access Control >>

** Warning:  The FLASH copy of UUA.EL1 is either not present or corrupt

Partition 0: Empty  **ACTIVE**
Partition 1: Empty

Enter BOOT Area Terminal Access password: xxxxxx

(1) File Download
(2) Switch Partitions
(3) Display File Directory


Make selection (1,2,3): 3
                 Size                                     Base  
               --------                                ---------
Partition 0:  (ACTIVE)
uuaTbolt EL1         0h                                                 0h
lmaTbolt EL0         0h                                                40h
sspTbolt L21         0h                                               C40h

Partition 1:
     UUA EL1         0h                                              8000h
     LMA EL0         0h                                              8040h
SSP_LOAD L21         0h                                              8C40h

Upper Partition:
SSP_DIAG O21         0h                                             10000h
  SYSTEM DMP         0h                                             10800h
    DATA DAT         0h                                          FFF80000h
    BOOT EL2     20000h  09/28/2005 02:38    08.00.01  2         FFFE0000h

Make selection (1,2,3): 2
Partitions have been switched.
You must now Power-cycle the unit (POR).

Initialize CF.... DONE

cf_binfile_check(): MAGIC 0

call boot_dwnld(1)


<< BOOT Area Terminal Access Control >>

** Warning:  The FLASH copy of UUA.EL1 is either not present or corrupt

Partition 0: Empty
Partition 1: Empty  **ACTIVE**

Enter BOOT Area Terminal Access password: xxxxxx

(1) File Download
(2) Switch Partitions
(3) Display File Directory

Make selection (1,2,3): 1
You must download the file UUA.EL1
Begin file download (hit CTRL-X five times to abort)...

Filename............. None
Download status...... FAILED - ZFILE/ZCRCW FRAME NOT RECEIVED

Hit any key to re-boot...

Occasional Contributor
Posts: 5
Registered: ‎04-10-2008

Re: Mcdata 4400 can't startup

The compact flash card contains nothing to boot from so there is no way to recover the switch easily.

If you have an identical switch you may be able to make a copy of the compact flash card, but that involves disassembling the 'good' switch and is full of risk that you will end up with two dead switches.

I would normally just recommend replacement of the switch.

External Moderator
Posts: 4,780
Registered: ‎02-23-2004

Re: Mcdata 4400 can't startup

which CF card is to copy ?

TechHelp24
New Contributor
Posts: 2
Registered: ‎03-20-2010

Re: Mcdata 4400 can't startup

Thank you very much.

The CF card isn't to copy .

I have the EOSv08.00.01.bin.

If i can looking for a z-modem transfer through white a serial cable?

N/A
Posts: 1
Registered: ‎01-04-2012

Re: Mcdata 4400 can't startup

Hello,

My name is Hipolito

Do you know the password for BOOT Area Terminal Access password?

I'm trying many passwords but do not have success

Regards

Hipolito

Join the Community

Get quick and easy access to valuable resource designed to help you manage your Brocade Network.