Fibre Channel (SAN)

Reply
N/A
Posts: 1
Registered: ‎10-22-2012

DCX - Firmwarecommit failed. (0x1a)

Hi,

I try to upgrade firmware version from 6.4.0c to v7.0.0c via CLI, on Brocade DCX, ones CP switch upgrade fine but the other CP has this error, I reboot the CP and try to execute firmwarecommit again, but I can't do anything, all firmware commands fails. See below the output commands

DCX:admin> firmwareshow

Slot Name       Appl     Primary/Secondary Versions               Status

--------------------------------------------------------------------------

  6  CP0        FOS      v7.0.0c                                  ACTIVE

                         v7.0.0c

  7  CP1        FOS      v7.0.0c                                  STANDBY *

                         Unknown

*  Local CP

WARNING: Firmwaredownload is in progress.

DCX:admin> firmwaredownload -s

Server Name or IP Address: 192.168.0.50

User Name: laraujo

File Name: /brocade/V7.0.0c

Network Protocol(1-auto-select, 2-FTP, 3-SCP, 4-SFTP) : 2

Password:

Do Auto-Commit after Reboot :

Reboot system after download : y

Server IP: 192.168.0.50, Protocol IPv4

Checking system settings for firmwaredownload...

Sanity check failed because firmwareDownload is already in progress.

DCX:admin> firmwarecommit -f

Validating the filesystem ...

Repairing the secondary partition now.

Please wait ...

rsync: writefd_unbuffered failed to write 4 bytes : Broken pipe (32)

rsync: write failed on "/mnt/boot/zImage.tree.initrd": No space left on device (28)

rsync error: error in file IO (code 11) at receiver.c(258)

rsync: connection unexpectedly closed (151107 bytes received so far)

rsync error: error in rsync protocol data stream (code 12) at io.c(453)

rsync: connection unexpectedly closed (1306 bytes received so far)

rsync error: error in rsync protocol data stream (code 12) at io.c(453)

rsync: writefd_unbuffered failed to write 4 bytes : Broken pipe (32)

rsync: write failed on "/mnt/boot/bootrom.bin": No space left on device (28)

rsync error: error in file IO (code 11) at receiver.c(258)

rsync: connection unexpectedly closed (151107 bytes received so far)

rsync error: error in rsync protocol data stream (code 12) at io.c(453)

rsync: connection unexpectedly closed (1262 bytes received so far)

rsync error: error in rsync protocol data stream (code 12) at io.c(453)

rsync: writefd_unbuffered failed to write 32768 bytes : Broken pipe (32)

rsync: write failed on "/mnt/boot/zImage.tree.initrd": No space left on device (28)

rsync error: error in file IO (code 11) at receiver.c(258)

rsync: connection unexpectedly closed (151107 bytes received so far)

rsync error: error in rsync protocol data stream (code 12) at io.c(453)

rsync: connection unexpectedly closed (1306 bytes received so far)

rsync error: error in rsync protocol data stream (code 12) at io.c(453)

Failed to synchronize the partitions (0xc00).

Please reboot the switch and run the firmwarecommit command. If the issue persists, Replace the CF card.

DCX:admin> firmwaredownloadstatus

: Sun Oct 21 02:04:33 2012

Slot 7 (CP1, active): Firmware is being downloaded to the switch. This step may take up to 30 minutes.

: Sun Oct 21 02:12:02 2012

Slot 7 (CP1, active): Relocating an internal firmware image on the CP blade.

: Sun Oct 21 02:14:36 2012

Slot 7 (CP1, active): The internal firmware image is relocated successfully.

: Sun Oct 21 02:14:37 2012

Slot 7 (CP1, active): Firmware has been downloaded to the secondary partition of the switch.

: Sun Oct 21 02:32:01 2012

Slot 7 (CP1, standby): The firmware commit operation has started. This may take up to 10 minutes.

: Sun Oct 21 02:37:27 2012

Slot 7 (CP1, standby): Firmware commit failed - Firmwarecommit failed. (0x1a)

: Sun Oct 21 02:37:55 2012

Slot 7 (CP1, standby): The firmware commit operation has started. This may take up to 10 minutes.

: Sun Oct 21 02:38:41 2012

Slot 7 (CP1, standby): Firmware commit failed - Firmwarecommit failed. (0x1a)

: Sun Oct 21 03:44:02 2012

Slot 7 (CP1, standby): The firmware commit operation has started. This may take up to 10 minutes.

: Sun Oct 21 03:44:47 2012

Slot 7 (CP1, standby): Firmware commit failed - Firmwarecommit failed. (0x1a)

Any sugestions?

Valued Contributor
Posts: 761
Registered: ‎06-11-2010

Re: DCX - Firmwarecommit failed. (0x1a)

did you connect directly to the Stby CP in order to execute those commands? If did not, try executing them connected via SSH/telnet to the Stby CP. If already done it that way, reboot the Stby CP. Last option would be to replace the CP.

Join the Community

Get quick and easy access to valuable resource designed to help you manage your Brocade Network.