Ethernet Switches & Routers

Reply
Contributor
Posts: 22
Registered: ‎03-16-2015

fastIronsx800 switch need help to resove the error

login:

EK_CORE_SWITCH>enable

Password:

EK_CORE_SWITCH#show run

Current configuration:

!

ver 04.3.00T3e1

!

module 1 fi-sx4-24-port-gig-copper-module

module 2 fi-sx4-24-port-gig-copper-module

module 4 fi-sx4-24-port-gig-fiber-module

module 9 fi-sx-0-port-management-module

!!!!!!!!

enable super-user-password .....

hostname EK_CORE_SWITCH

ip address 10.1.10.100 255.240.0.0

ip default-gateway 10.1.1.1

 

!!!!!!

end

EK_CORE_SWITCH#show trunk

Configured trunks:

None

Operational trunks:

None

EK_CORE_SWITCH#show vlan

Total PORT-VLAN entries: 1

Maximum PORT-VLAN entries: 64

legend: [S=Slot]

EK_CORE_SWITCH#show run

Current configuration:

FastIron-Sx800 config.txt[2/19/2015 7:00:44 PM]

!

ver 04.3.00T3e1

!

module 1 fi-sx4-24-port-gig-copper-module

module 2 fi-sx4-24-port-gig-copper-module

module 4 fi-sx4-24-port-gig-fiber-module

module 9 fi-sx-0-port-management-module

!!!!!!!!

enable super-user-password .....

hostname EK_CORE_SWITCH

ip address 10.1.10.100 255.240.0.0

ip default-gateway 10.1.1.1

 

!!!!!!

end

EK_CORE_SWITCH#

EK_CORE_SWITCH(config)#Power supply 3 is down

Power supply 3 (from left when facing front side) failed. Fail cause: NO DC/DC E

NABLED

SXR Boot Code Version 04.0.00

Enter 'a' to stop at memory test

Enter 'b' to stop at boot monitor

BOOT INFO: load monitor from primary, size = 191080

BOOT INFO: load image from primary

BOOT INFO: bootparam at 0008ee18, mp_flash_size = 00243c61

BOOT INFO: code decompression completed

BOOT INFO: branch to 00400100

Pre Parsing Config Data ...

..Info: Fan Tray 1 detected.

Error - Lincard module at slot 3 does not match existing linecard module

Validating the line modules ......DONE

P1 : 00 01 02 03 06 07

F1 : 00 01 02 03 06 07

FX1: 00 01 02 03 06 07

FastIron-Sx800 config.txt[2/19/2015 7:00:44 PM]

P2 : 00 01 02 03 06 07

F2 : 00 01 02 03 06 07

FX2: 00 01 02 03 06 07

Parsing Config Data ...

powered On switch Fabric 1

CX : 60

CX0 Mcast Init ................

CX : 61

CX1 Mcast Init ................

powered On switch Fabric 2

CX : 62

CX2 Mcast Init ................

CX : 63

CX3 Mcast Init ................

==========================================================================

Active Management CPU [Slot-9]:

SW: Version 04.3.00T3e1 Copyright (c) 1996-2008 Foundry Networks, Inc.

Compiled on Nov 14 2008 at 16:10:49 labeled as SXS04300

(2374753 bytes) from Primary sxs04300.bin

BootROM: Version 04.0.00T3e5 (FEv2)

HW: Chassis FastIron SX 800

Serial #: C8SA30E0AE

==========================================================================

SL 1: SX-FI424C 24-port Gig Copper

Serial #: CH21091767

P-ASIC 0: type 00D1, rev D2 subrev 00

P-ASIC 1: type 00D1, rev D2 subrev 00

==========================================================================

SL 2: SX-FI424C 24-port Gig Copper

Serial #: V50429F07B

P-ASIC 2: type 00D1, rev D2 subrev 00

P-ASIC 3: type 00D1, rev D2 subrev 00

==========================================================================

SL 4: SX-FI424F 24-port Gig Fiber

Serial #: CH29092743

P-ASIC 6: type 00D1, rev D2 subrev 00

P-ASIC 7: type 00D1, rev D2 subrev 00

==========================================================================

SL 9: SX-FIZMR4 0-port Management

Serial #: CH26091208

==========================================================================

Active Management Module:

660 MHz Power PC processor 8541 (version 32/0020) 66 MHz bus

512 KB boot flash memory

16384 KB code flash memory

512 MB DRAM

The system uptime is 27 seconds

The system : started=cold start

EK_CORE_SWITCH>

Power supply 3 (from left when facing front side) detected and up.

FastIron-Sx800 config.txt[2/19/2015 7:00:44 PM]

Power supply 4 (from left when facing front side) detected and up.

EK_CORE_SWITCH(config)#show module

Module Status Ports Starting MAC

F1: SX-FISF Switch Fabric active

F2: SX-FISF Switch Fabric active

S1: SX-FI424C 24-port Gig Copper OK 24 001b.eda5.5c00

S2: SX-FI424C 24-port Gig Copper OK 24 001b.eda5.5c18

S3:

S4: SX-FI424F 24-port Gig Fiber OK 24 001b.eda5.5c48

S5:

S6:

S7:

S8:

S9: SX-FIZMR4 0-port Management Active 0

{ Status : OK }

S10: Standby 0

EK_CORE_SWITCH(config)#

EK_CORE_SWITCH(config)#show version

==========================================================================

Active Management CPU [Slot-9]:

SW: Version 04.3.00T3e1 Copyright (c) 1996-2008 Foundry Networks, Inc.

Compiled on Nov 14 2008 at 16:10:49 labeled as SXS04300

(2374753 bytes) from Primary sxs04300.bin

BootROM: Version 04.0.00T3e5 (FEv2)

HW: Chassis FastIron SX 800

Serial #: C8SA30E0AE

==========================================================================

SL 1: SX-FI424C 24-port Gig Copper

Serial #: CH21091767

P-ASIC 0: type 00D1, rev D2 subrev 00

P-ASIC 1: type 00D1, rev D2 subrev 00

==========================================================================

SL 2: SX-FI424C 24-port Gig Copper

Serial #: V50429F07B

P-ASIC 2: type 00D1, rev D2 subrev 00

P-ASIC 3: type 00D1, rev D2 subrev 00

==========================================================================

SL 4: SX-FI424F 24-port Gig Fiber

Serial #: CH29092743

P-ASIC 6: type 00D1, rev D2 subrev 00

P-ASIC 7: type 00D1, rev D2 subrev 00

==========================================================================

SL 9: SX-FIZMR4 0-port Management

Serial #: CH26091208

==========================================================================

Active Management Module:

660 MHz Power PC processor 8541 (version 32/0020) 66 MHz bus

512 KB boot flash memory

16384 KB code flash memory

512 MB DRAM

The system uptime is 19 minutes 41 seconds

 

 

 

Please let me know the

 

  • Version details & model no: of existing cards
  • Version details & model no: of new card
  • Version details & model no: of core switch

Please let me know how to fix this error and what is the solution to resolve. Please consider this as an urgent

 

Regards

 

External Moderator
Posts: 4,811
Registered: ‎02-23-2004

Re: fastIronsx800 switch need help to resove the error

Hi,

 

First at all, I'm not the most Expert with this Plattforms.

 

from you Post, i understand you want to install New Card Module in the Switch, is this correct ?

 

the error you post, show to me:

 

1) Power Supply is missing,

or

2) Power Supply not Support the New Card module you want to Install.

 

please check the FSX FAQ

 

http://www.brocade.com/forms/getFile?p=documents/faqs/brocade-fsx-faq.pdf

 

 

 

 

 

TechHelp24
Contributor
Posts: 22
Registered: ‎03-16-2015

Re: fastIronsx800 switch need help to resove the error

hi,

 

We had installed the new card to the switch. the new card is not supporting.

should we upgrade anything?

If we upgrade to the new card will it effect to the existing cards

 

Regards

Biju

External Moderator
Posts: 4,811
Registered: ‎02-23-2004

Re: fastIronsx800 switch need help to resove the error

Hi,

 

>We had installed the new card to the switch. the new card is not supporting.

 

if the card is not Supported, you should check in the FAQ about the requirements.

 

i.e. some Card require NEW generation of Management Module.

 

I don't think the problem is related to Microcode

 

BTW and FYI : To avoid confusion, make no sense to open more Thread for the same Problem.

TechHelp24
Contributor
Posts: 22
Registered: ‎03-16-2015

Re: fastIronsx800 switch need help to resove the error

hi,

 

..Info: Fan Tray 1 detected.

 

Error - Lincard module at slot 3 does not match existing linecard module

Validating the line modules ......DONE

 

 

Is this error related to the new card not supporting.

 

Thanks

 

External Moderator
Posts: 4,811
Registered: ‎02-23-2004

Re: fastIronsx800 switch need help to resove the error

Correct, I think the card is not Supported because not matching with other Card or Management Module or the Power Supply.

 

Again, I'm not the most expert with this Plattforms, and would suggest if you have a Active maintenannce Contract to open a call with Brocade Support.

 

Otherwise post here all details Inventory with exact part Number and Model Number about the Installed Card Module, Management Module, and Power Supply, I'll try to find more Information.

 

try with Brocade NET-Health to collect all the info

 

http://www.brocade.com/services-support/drivers-downloads/Net-Health/index.page

 

 

TechHelp24
Contributor
Posts: 22
Registered: ‎03-16-2015

Re: fastIronsx800 switch need help to resove the error

hi,

 

I will arrange to send the installed card details . In the meantime is it possible to figure out with the below details

 

 

==========================================================================

Active Management CPU [Slot-9]:

SW: Version 04.3.00T3e1 Copyright (c) 1996-2008 Foundry Networks, Inc.

Compiled on Nov 14 2008 at 16:10:49 labeled as SXS04300

(2374753 bytes) from Primary sxs04300.bin

BootROM: Version 04.0.00T3e5 (FEv2)

HW: Chassis FastIron SX 800

Serial #: C8SA30E0AE

==========================================================================

 

 

Current configuration:

!

ver 04.3.00T3e1

!

module 1 fi-sx4-24-port-gig-copper-module

module 2 fi-sx4-24-port-gig-copper-module

module 4 fi-sx4-24-port-gig-fiber-module

module 9 fi-sx-0-port-management-module

 

 

Active Management Module:

660 MHz Power PC processor 8541 (version 32/0020) 66 MHz bus

512 KB boot flash memory

16384 KB code flash memory

512 MB DRAM

The system uptime is 27 seconds

The system : started=cold start

 

the letters in blue indicates the error message of the managment module

Contributor
Posts: 22
Registered: ‎03-16-2015

Re: fastIronsx800 switch need help to resove the error

hi,

Below are information i have related to the brocade switch

 

 

 

SX-FI-8XG        -     FastIron SX interface module, 8-port 10GE SFPP, universal support       -       S/N BQKO402K02J

10G-SFPP-LR  -     10GBASE-LR, SFP+ optic (LC), for up to 10km over SMF  - S/N :ADF21352000185E, ADF213520000ETG

E1MG-SX-OM  -      1000BASE-SX SFP Optic      S/N  : TAA11434MA3V,TAA11434MA4U

 

 

ICX6450-24P  -   Brocade 24-port 1G Switch PoE+ 780W, 2x1G SFP+  & 2x1G/10G SFP+ Uplink/Stacking Ports  - S/N: BZR0411K048

 

ICX6450-24P   -  24-port 1G Switch PoE+  S/N: BZR3231K02J

 

Please let me know these information is okay with you

 

Thanks

External Moderator
Posts: 4,811
Registered: ‎02-23-2004

Re: fastIronsx800 switch need help to resove the error

Hi,

 

you have follow Module Installed

 

S1: SX-FI424C 24-port Gig Copper - second generation

S2: SX-FI424C 24-port Gig Copper - second generation

S4: SX-FI424F 24-port Gig Fiber - first generation

S9: SX-FIZMR4 0-port Management


The SX-FI-8XG you want to Install, is Third Generation Module.
Now, depend which management Modules you have in the Chassis, Third generation Module cannot coexist in the same chassis.

 

 

from the FAQ

 

FastIron SX third-generation interface modules were introduced in November 2011.
Unlike earlier modules, they have the unique capability to run with either first- or secondgeneration
management modules and can operate with either first- or second-generation
interface modules in the same chassis.

 

as per my understand, - but is proable I'm wrong here - new third generation SX Module can only be used with first ( only ) or with second ( only ) generation and not mixed First, Second and Third in the same Chassis.

 

 

continue.....

 

Q Can the first-, second-, and third-generation modules of the FastIron SX Series be mixed
in a chassis?
A IPv4-only first-generation and IPv6-capable second-generation modules or management
modules cannot coexist in the same chassis. First-generation interface modules can be
used only in a chassis with first-generation management modules. The secondgeneration
interface modules can be used only in a chassis with second-generation or 0-
port third-generation management modules. The 48-port 10/100/1000 Mbps interface
module, introduced in mid 2010, and the third-generation interface modules, introduced
in November 2011, operate with either first- or second-generation modules when
installed in a system with associated first- or second-generation management modules.
Third-generation XL series management modules do not allow for mixing second- and
third-generation interface modules. The SX-FI-ZMR-XL management module can operate
with either all second- or all third-generation modules installed. The SX-FI-2XGMR-XL
management modules will only interoperate with all third-generation interface modules.

TechHelp24
Contributor
Posts: 22
Registered: ‎03-16-2015

Re: fastIronsx800 switch need help to resove the error

[ Edited ]

Hi,

Thanks for the valuable solution.

 

1. So now what kind of managment module i can install

 

 

2.Or else please let us know which module to be installed and make this switch working

 

3. what generation is this chasis?

 

Regards

Join the Community

Get quick and easy access to valuable resource designed to help you manage your Brocade Network.