Ethernet Switches & Routers

Reply
New Contributor
Posts: 3
Registered: ‎03-29-2012

Need Assistance for Fastiron Edge 4802

hi,

we are purchased Fastiron Edge 4802 last year. Now no vendor is available in pakistan to provide support. we need to make VLANs and assign IP. unformtunately we are unable to perform the required action. Please provide assistance.

regards,

Muhammad SHoeb

Super Contributor
Posts: 1,087
Registered: ‎12-13-2009

Re: Need Assistance for Fastiron Edge 4802

Hi muhammad.shoeb,

     Please post the output of both of these commands 'show ver' and 'show flash'.

to create a VLAN

     * from the config level

     * type vlan 100

     * tag ethernet 1 (to use the first ethernet port as a tagged port - Cisco speak would be trunk port)

     * untag ethernet 2 to 10 ( to assign ports 2 to 10 as memebr of vlan 100)

IP address will depend on what code you are running.

Thanks

Michael.

New Contributor
Posts: 3
Registered: ‎03-29-2012

Re: Need Assistance for Fastiron Edge 4802

BR-telnet@FES4802 Router>show version
  SW: Version 03.7.00Tc1 Copyright (c) 1996-2006 Foundry Networks, Inc.
      Compiled on Dec 27 2006 at 18:16:04 labeled as FEL03700
      (2753059 bytes) from Primary FEL03700.bin
      Boot Monitor: Version 03.5.00Tc4
  HW: Stackable FES4802
==========================================================================
      Serial #: FL18030314
  330 MHz Power PC processor 8245 (version 129/1014) 66 MHz bus
  512 KB boot flash memory
16384 KB code flash memory
  128 MB DRAM
The system uptime is 5 days 52 minutes 22 seconds
The system : started=cold start

BR-telnet@FES4802 Router>show flash
Compressed Pri Code size = 2753059, Version 03.7.00Tc1 (FEL03700.bin)
Compressed Sec Code size = 2753059, Version 03.7.00Tc1 (FEL03700.bin)
Compressed Boot-Monitor Image size = 49021, Version 03.5.00Tc4
Compressed Boot-Tftp Code size = 184111, Version 03.5.00Tc5
Default BootROM Contents Info:
   Boot Loader Rev: 1a
   Monitor Image Version: 01.00.00Tc4
   Boot-Tftp Image Version: 01.00.00Tc5
Code Flash Free Space = 10747904
BR-telnet@FES4802 Router>

please guide us for the following scenerio

1. on foundry Switch we have 48 ports and 2 optical fiber ports,  both optical fiber module will be connecting with 2 cisco 3560 switches. we will use HSRP in cisco switches for redundancy.

2. we will connect foundry switch from port #48 to a cisco  SGE2000Pswitch

3. we want to create vlans as follows

VLAN ID

VLAN Name

10

Switches

11

Servers

21

STORAGE LAN

22

SERVER LAN

23

CLIENT LAN

24

CONTROL LAN

50

IT

51

APD

52

Marketing 1

53

Marketing 2

54

HR

55

SupplyChain-Mgmt

56

Admin

57

Engineering

58

Production-Planning

59

Distribution

60

FICO

61

Audit

62

Import

63

War-room

64

Production

65

BIOTech

66

Directors

67

Compliance

68

QA

69

QC

70

FG

4. all interVLAN routing will be done by CISCO 3560 Switch

5. Configure the Optical fiber port as trunk for all VLAN (please keep in mind that CISCO SGE2000 will also use those trunks.)

6. How to assign IP address to FOUNDRY SWITCH FOR REMOTE MANAGEMENT as all ports will be in VLAN. i

i would be very grateful for your efforts.

please see attachment for switches placement

shoeb

Super Contributor
Posts: 1,087
Registered: ‎12-13-2009

Re: Need Assistance for Fastiron Edge 4802

Hi muhammad.shoeb,

Tag = Cisco switch mode trunk

Untag = switch mode access

Sample config from the config term level

Vlan 10 name Switches

Tag Ethernet 48

Untag Ethernet x

Vlan 11 name Servers

Tag Ethernet 48

Untag Ethernet x

Vlan 21 name STORAGE LAN

Tag Ethernet 48

Untag Ethernet x

Vlan 22 name SERVER LAN

Tag Ethernet 48

Untag Ethernet x

Vlan 23 name CLIENT LAN

Tag Ethernet 48

Untag Ethernet x

Vlan 24 name CONTROL LAN

Tag Ethernet 48

Untag Ethernet x

Where X = the member port you want to assign to the VLAN

Their may be a better way but I know remmeber if that switch code supports VLAN Groups

e.g.

Configuring a VLAN group
To configure a VLAN group, enter commands such as the following.
FastIron(config)#vlan-group 1 vlan 2 to 1000
FastIron(config-vlan-group-1)#tagged 48
The first command in this example begins configuration for VLAN group 1, and assigns VLANs 2 through 1000 to the group. The second command adds ports 1/1 and 1/2 as tagged ports. Since all the VLANs in the group share the ports, you must add the ports as tagged ports.
Syntax: vlan-group <num> vlan <vlan-id> to <vlan-id>

Management IP address

As you are using a layer 3 code, you would create a VE on VLAN 1

e.g.

vlan 1

router-interface ve 1

int v 1

ip address x.y.z.a/b

Thanks

Michael.

New Contributor
Posts: 3
Registered: ‎03-29-2012

Re: Need Assistance for Fastiron Edge 4802

hi,

thanks for help.

we have made up vlans. working ok.

for trunk i asked you configuration for optical fiber module as we will use them as trunk which will connect to our distribution switch CISCO 3560 .

lastly we are unable to connect foundry switch for management through IP.

please help.

shoieb

Join the Community

Get quick and easy access to valuable resource designed to help you manage your Brocade Network.