Ethernet Switches & Routers

Reply
New Contributor
Posts: 2
Registered: ‎05-06-2013

ICX 6450 24 port switch

I have a ICX 6450 24 port switch that I am trying to partition into 2 layer3 vlans. I created vlan 3 and vlan 13 and added untagged ports 3-12 to vlan 3 and 13 to 23 for vlan 13.

vlan 3 by port

tagged ethe 1/1/1 ethe 1/1/24

untagged ethe 1/1/3 ethe 1/1/12

!

vlan 13 by port

tagged ethe 1/1/1 ethe 1/1/24

untagged ethe 1/1/13 ethe 1/1/23

I wanted to add a virtual router to each vlan

router-interface ve 3

interface ve 3

ip address 10.0.3.3/24

but I can't create router-interface ve 3,

switch1(config-vlan-3)#

atalk-proto            Set AppleTalk protocol VLAN
  clear                  Clear table/statistics/keys
  decnet-proto           Set decnet protocol VLAN
  default-gateway        Set the default gateway for the management-vlan
  end                    End Configuration level and go to Privileged level
  exit                   Exit current level
  ip-proto               Set IP protocol VLAN
  ip-subnet              Set IP subnet VLAN
  ipv6-proto             Set IPv6 protocol VLAN
  ipx-network            Set IPX network VLAN
  ipx-proto              Set IPX protocol VLAN
  loop-detection         shut down ports if receiving packets from myself
  mac-vlan-permit        Define port to be used for MAC Based VLan
  management-vlan        Dedicate this vlan for management purpose
  metro-ring             metro ring configuration mode
  metro-rings            metro ring-ids configured in the vlan across the
                         network
  mld-snooping           IPv6 MLD snooping on this VLAN
  monitor                Monitor Ingress Traffic on this VLAN (Enable VLAN
                         Mirroring)
  multicast              IGMP snooping on this VLAN
  netbios-proto          Set netbios protocol VLAN
  no                     Undo/disable commands
  other-proto            Set other protocol VLAN        
  pvlan                  Define private vlan type and mapping
  quit                   Exit to User level
  show                   Show system information
  spanning-tree          Set spanning tree for this VLAN
  static-mac-address     Configure static MAC for this VLAN
  tagged                 802.1Q tagged port
  untagged               Port with only untagged frame in/out
  uplink-switch          Define uplink port(s) and enable uplink switching
  vsrp                   Configure VSRP
  vsrp-aware             Configure VSRP Aware parameters
  webauth                Set web authentication
  write                  Write running configuration to flash or terminal

cust1(config-vlan-3)#sh ver

  Copyright (c) 1996-2012 Brocade Communications Systems, Inc. All rights reserved.

    UNIT 1: compiled on Mar  2 2012 at 12:38:17 labeled as ICX64S07400

                (10360844 bytes) from Primary ICX64S07400.bin

        SW: Version 07.4.00T311

  Boot-Monitor Image size = 512, Version:07.4.00T310 (kxz07400)

  HW: Stackable ICX6450-24

Do I need another version of the firmware or is this a limitation of this particular switch?

Brocadian
Posts: 152
Registered: ‎10-05-2010

Re: ICX 6450 24 port switch

You are using the switch code now. If you boot from your layer 3 image, your software version (#sh ver) will be ICX64R07400.bin. Please look the link below for more information on booting into your layer 3 code.

http://community.brocade.com/docs/DOC-1842

Join the Community

Get quick and easy access to valuable resource designed to help you manage your Brocade Network.