Ethernet Switches & Routers

Reply
N/A
hhassan
Posts: 1
Registered: ‎05-10-2012

Fastiron SX 800 Unknown module id: 0x6e/0x6c error

Hello Every one,

                                 Hope you are fine like me. I have installed two Modules of SX-FI-24HF in Slot 1 and slot 2. Two more modules of SX-FI-2XG in slot # 7 and 8.

Two Management Modules in Slot # 9 and 10.

Fabric and Management Modules are up. But Interface slots 1,2,7,8 is not powering up as you can see below it says "Unknown module id: 0x6e.

Error during powering on the module at slot 1"

Kindly let me know your suggestions. Do i need to upgrade firmware ?

I have tried by replacing the modules in different slots but results are same.

If i need to upgrade firmware or image. Which version is recommended?. 7400?

a or b?.

Looking FWD for your assistance.

Kind Regards.

Hammad

=======================================================================

SXR Boot Code Version 05.0.00

Enter 'a' to stop at memory test

Enter 'b' to stop at boot monitor

BOOT INFO: load monitor from primary, size = 191953

Appln_Monitor:root_task: ***local_overide = 0***

BOOT INFO: debug enabled!!!

BOOT INFO: load image from primary

BOOT INFO: bootparam at 0008f3e4, mp_flash_size = 0033dbcb

BOOT INFO: code decompression completed

BOOT INFO: branch to 00400100

Pre Parsing Config Data ...

..Info: Fan Tray 1 detected.

Unknown module id: 0x6e.

Error during powering on the module at slot 1

Unknown module id: 0x6e.

Error during powering on the module at slot 2

Unknown module id: 0x6c.

Error during powering on the module at slot 7

Unknown module id: 0x6c.

Error during powering on the module at slot 8

Validating the line modules ......DONE

P1 :

F1 :

FX1:

P2 :

F2 :

FX2:

Parsing Config Data ...

powered On switch Fabric 1

CX : 60

CX0 Mcast Init .........

Active : Detected Stdby heart-beat

.......

CX : 61

CX1 Mcast Init ................

powered On switch Fabric 2

CX : 62

CX2 Mcast Init ................

CX : 63

CX3 Mcast Init ................

==========================================================================

Active Management CPU :

SW: Version 05.1.00dT3e3 Copyright (c) 1996-2009 Brocade Communications Systems, Inc.

Compiled on Jun 02 2010 at 15:49:22 labeled as SXR05100d

(3398603 bytes) from Primary /foundry/SX/os/SXR05100d.bin

BootROM: Version 05.0.00T3e5 (FEv2)

Serial  #: B32538****

HW: Chassis FastIron SX 800-PREM (PROM-TYPE SX-FIL3U-6-IPV4)

==========================================================================

SL 9: SX-FIZMR4 0-port Management

Serial  #: W10419****

==========================================================================

Active Management Module:

660 MHz Power PC processor 8541 (version 32/0020) 66 MHz bus

512 KB boot flash memory

16384 KB code flash memory

512 MB DRAM

Monitor Option is on

The system uptime is 24 seconds

The system : started=cold start 

Initializing the standby management module in slot 10....please wait

Bringing up module 10 ...

Module 10 is now up and running

IPC ready on peer mgmt module.

Config file synchronization done.

FastIron SX 800 Router>

SSH host key synchronization done.

FastIron SX 800 Router>

SSH public key synchronization

DHCP Snoop data file synchronization

SSL certificate synchronization done.

FastIron SX 800 Router>

DHCP Snoop data file synchronization

SSL certificate synchronization done.

FastIron SX 800 Router>

SSL certificate synchronization done.

FastIron SX 800 Router>Synchronizing with standby module...

Synchronizing with standby module...

Join the Community

Get quick and easy access to valuable resource designed to help you manage your Brocade Network.