Ethernet Switches & Routers

Reply
New Contributor
Posts: 3
Registered: ‎12-09-2015

6610 CLI commands

For some reason the only CLI commands I have available in 'enable' mode are;

 configure           Enter configuration mode
 exit                Exit Privileged mode
 fips                FIPS execution commands
 mrinfo              Multicast route query
 page-display        Display data one page at a time
 ping                Ping IP node
 quit                Exit to User level
 show                Display system information
 skip-page-display   Enable continuous display
 ssh                 SSH by name or IP address / hostkeys
 stop-traceroute     Stop TraceRoute operation
 telnet              Telnet by name or IP address
 trace-l2            TraceRoute L2
 traceroute          TraceRoute to IP node
 verify              Verify object contents

 

anybody else experienced this ??

 

Many thanks

Dave

Frequent Contributor
Posts: 97
Registered: ‎07-12-2011

Re: 6610 CLI commands

What else are you looking for?

 

show commands pull info, try show ?

 

you have to get into config mode to do configurations

 

conf t

 

then you can use the ? to get config commands.

New Contributor
Posts: 3
Registered: ‎12-09-2015

Re: 6610 CLI commands

Thanks for reply.

The problem I have is that not all CLI commands are available when I enter ' en ' mode ?

Occasional Contributor
Posts: 8
Registered: ‎10-14-2014

Re: 6610 CLI commands

The following commands are available:

  alias                        Display configured aliases

  boot                         Boot system from bootp/tftp server/flash image

  clear                        Clear table/statistics/keys

  clock                        Set clock

  configure                    Enter configuration mode

  copy                         Copy between flash, tftp, scp, config/code

  debug                        Enable debugging functions (see also 'undebug')

  disable                      Disable system monitoring

  dot1x                        802.1X

  downgrade_to                 downgrade to a version prior to 8.0

  enable                       Enable system monitoring

  erase                        Erase image/configuration from flash

  execute                      Execute commands in batch

  exit                         Exit Privileged mode

  fips                         FIPS execution commands

  inline                       Inline power (PoE) configuration/operation

  jitc                         JITC execution commands

  kill                         Kill active CLI session

  license                      Delete software licenses

  page-display                 Display data one page at a time

  phy                          PHY related commands

  ping                         Ping IP node

  port                         Port security command

  quit                         Exit to User level                 

  rconsole                     Use the console of another unit

  reload                       Halt and perform a warm restart

  show                         Display system information

  simulate-non-stacking-unit   Simulate the absence of the stacking PROM

  skip-page-display            Enable continuous display

  ssh                          SSH by name or IP address / hostkeys

  stack                        stacking run-time commands

  stop-traceroute              Stop TraceRoute operation

  supportsave                  support save related

  telnet                       Telnet by name or IP address

  temperature                  temperature sensor commands

  terminal                     display syslog

  trace-l2                     TraceRoute L2

  traceroute                   TraceRoute to IP node

  undebug                      Disable debugging functions (see also 'debug')

  verify                       Verify object contents

  whois                        WHOIS lookup

  write                        Write running configuration to flash or terminal

 

This switch is running the L3 Routing image FCXR08030b.

 

If this is not a clean switch check the config for restrictions on users or TACACS/RADIUS.

 

Swen

Frequent Contributor
Posts: 97
Registered: ‎07-12-2011

Re: 6610 CLI commands

What code is on the box, can you paste a show run?

Join the Community

Get quick and easy access to valuable resource designed to help you manage your Brocade Network.